AP Chemistry · Unit 5: Kinetics

5.10 Multistep Reaction Energy Profile

Essential Question

How does an energy profile show each step of a mechanism?

In Topic 5.6 you drew one hill for one elementary step. In this topic you will combine mechanisms and energy profiles to draw a profile for a reaction with several steps.

Video not loading? Watch it on YouTube.

One Hill per Step

  • Each elementary step has its own energy hill.
  • Each hill has its own transition state (TS) at the top.
  • A two-step mechanism has two hills; a three-step mechanism has three.
Two-step energy profile with two hills, labeled TS 1 and TS 2. Products end lower than reactants.

Read the graph from left to right, just like the mechanism: the reactants climb the first hill in step 1, then the second hill in step 2, and end up as products.

Intermediates in the Valleys

  • The valley between two hills is an intermediate: the product of one step and the reactant of the next.
  • An intermediate sits in a dip in energy, so it is a little bit stable and can sometimes be detected.
  • A transition state sits at the top of a hill and cannot be isolated at all.
Two-step energy profile with a purple dot in the valley between the two hills, labeled intermediate.

Finding the Slow Step

  • The rate-determining step is the step with the largest Ea.
  • Measure each Ea from the bottom of that step, not from the start of the graph.
  • Step 1’s Ea goes from the reactants to the first peak; step 2’s goes from the intermediate to the second peak.
Two-step energy profile. A tall red arrow Ea1 goes from the reactants to the first peak; a short blue arrow Ea2 goes from the valley to the second peak.

Here, Ea1 is much bigger than Ea2, so step 1 is the slow step.

Overall ΔH

  • ΔH = energy of products − energy of reactants.
  • Only the start and end levels matter; the hills and valleys in between do not change ΔH.
Two-step energy profile with a red delta H arrow pointing down from the reactant level to the product level.

Here the products are lower than the reactants, so the overall reaction is exothermic. Individual steps can differ: in this profile, step 1 goes uphill to the intermediate and step 2 goes downhill.

Drawing a Multistep Profile

  1. Place the reactant and product levels: products lower if ΔH < 0, higher if ΔH > 0.
  2. Draw one hill for each elementary step.
  3. Put a valley between the hills for each intermediate.
  4. Make the slow step’s hill the biggest, measured from where that step starts.

If a step is endothermic, it ends higher than where it started; if it is exothermic, it ends lower.

↑ Back to top


Worked Examples

Try each problem on your own first, then open the solution to check your work.

Example 1: Reading a Multistep Profile

Use the energy profile to find: the number of steps, the number of intermediates, the rate-determining step, and whether the reaction is exothermic or endothermic.

Three-step energy profile: a small first hill, a tall second hill rising from the first valley, and a small third hill. Products end lowest.
Show the solution
  1. Count the hills: Three peaks, so 3 elementary steps.
  2. Count the valleys: Two valleys between the hills, so 2 intermediates.
  3. Compare activation energies: Measure each Ea from the bottom of its own step. Steps 1 and 3 have small hills; step 2 climbs from the first valley to the highest peak. Step 2 is rate-determining.
  4. Compare start and end: The products are lower than the reactants, so the reaction is exothermic (ΔH < 0).

Example 2: Sketching a Profile

A two-step reaction has a slow, endothermic first step and a fast, exothermic second step. The overall reaction is exothermic. Sketch the energy profile.

Show the solution
  1. Place the levels: Draw the reactant level about halfway up on the left and a lower product level on the right (overall exothermic).
  2. Draw step 1: Draw a tall hill rising from the reactants (slow step). Come down into a valley that is higher than the reactants (endothermic step). Label it “intermediate.”
  3. Draw step 2: From the valley, draw a small hill (fast step), then drop all the way down to the product level (exothermic step).
  4. Label it: Label Ea1 (big) and Ea2 (small) with arrows, and draw ΔH pointing down from the reactant level to the product level.

Example 3: Matching a Mechanism

In a two-step mechanism, step 1 is fast and step 2 is slow. Which energy profile matches?

Two energy profiles. Profile A: the first hill is taller than the second. Profile B: the first hill is small and the second hill is the tallest.
Show the solution
  1. Use the rule: The slow step has the largest Ea, so step 2 needs the bigger hill (measured from the valley).
  2. Check profile A: The first hill is huge and the second hill is small, so step 1 would be slow. Not a match.
  3. Check profile B: The first hill is small, and the second hill rises from the valley to the highest point. Step 2 has the bigger activation energy.
  4. Answer: Profile B matches a fast first step and a slow second step.

↑ Back to top


Practice

Practice with the Kinetics and Collision Theory Sandbox

Watch particles collide, change the temperature, the concentration and the activation energy, add a catalyst, and see why only some collisions lead to a reaction.

Lab worksheet: PDF | Answer key: PDF

Practice with instant feedback

Answer original AP-style questions for Unit 5 and see an explanation right after each one. Choose Topic 5.10 or mix topics. No login needed.

↑ Back to top


Lesson Slides

↑ Back to top


Big Ideas

  • Each elementary step has its own hill with its own transition state.
  • The valleys between hills are intermediates.
  • The step with the largest Ea, measured from where that step starts, is the rate-determining step.
  • Overall ΔH is still products − reactants.

Back to the essential question: Every step is a hill, every intermediate is a valley, and the biggest climb tells you the slow step. Hills = steps, valleys = intermediates. Next up, Topic 5.11 Catalysis, where you will see how catalysts change these energy profiles.

↑ Back to top


AP Alignment

This lesson covers Topic 5.10, Multistep Reaction Energy Profile, in Unit 5 (Kinetics) of the College Board AP Chemistry Course and Exam Description (CED). Learning objective:

  • 5.10.A: Represent the activation energy and overall energy change in a multistep reaction with a reaction energy profile.

Essential knowledge: 5.10.A.1

Suggested skill: 3.B Representing Data and Phenomena. Represent chemical substances or phenomena with appropriate diagrams or models (e.g., electron configuration).

↑ Back to top