AP Chemistry · Unit 5: Kinetics

5.5 Collision Model

Essential Question

Why don’t all collisions cause a reaction?

In a gas at room temperature, each particle collides billions of times every second. If every collision caused a reaction, every reaction would be over instantly. So something else must be going on.

Video not loading? Watch it on YouTube.

Particles Must Collide

  • Particles have to collide to react.
  • During a collision, old bonds can break and new bonds can form.
  • Rate depends on collisions per second, so more collisions usually means a faster reaction.
A box of red and blue gas particles moving in different directions, with a starburst where one red and one blue particle collide.

But not every collision counts. A collision has to pass two tests: enough energy and the right orientation.

Test 1: Enough Energy

  • The minimum energy needed to react is the activation energy, Ea.
  • Slow particles that collide gently just bounce apart.
  • Fast particles that collide hard enough to reach Ea can react.
Left panel, low energy: slow particles A and B collide and bounce apart. Right panel, enough energy: fast particles A and B collide and react to form AB.

Test 2: Correct Orientation

  • Particles have to hit each other in the right spot.
  • Here, atom C must bond to atom A to make the product.
Left panel, wrong orientation: atom C hits the B end of molecule BA, no reaction. Right panel, right orientation: C hits the A end of molecule AB.

If C hits the B end of the molecule, there is no reaction, even with plenty of energy. A successful collision needs both enough energy and the right orientation.

Energy of Collisions

  • The Maxwell-Boltzmann distribution (from Unit 3) shows the range of particle kinetic energies.
  • Most particles are near the peak; only a few have very high energy.
  • The shaded area past Ea is the fraction of particles with enough energy to react.
Distribution of particle kinetic energies with a dashed line at the activation energy Ea. The small area under the curve to the right of Ea is shaded.

That fraction is usually small, which is one big reason most collisions do not lead to a reaction.

Effect of Temperature

  • At a higher temperature (T2), the curve shifts right and flattens.
  • The area under each curve is the same, because it is the same number of particles.
  • A much larger fraction of particles has energy ≥ Ea, so more collisions are successful.
Energy distributions at two temperatures. The higher temperature T2 curve is flatter and shifted right, with a larger shaded area past Ea than the T1 curve.

Particles also collide a little more often at higher temperature, but the bigger effect is that more collisions have enough energy.

Effect of Concentration

  • More particles in the same space collide more often.
  • More collisions per second means more successful collisions per second.
  • The fraction of collisions that succeed stays the same.
Two boxes of the same size. Low concentration has 4 particles; high concentration has 10 particles.

↑ Back to top


Worked Examples

Try each problem on your own first, then open the solution to check your work.

Example 1: Explaining Temperature

Use the collision model to explain why a reaction is faster at 50 °C than at 25 °C.

Show the solution
  1. Start with temperature: Higher temperature means a higher average kinetic energy.
  2. Connect to activation energy: At the higher temperature, a larger fraction of collisions have energy ≥ Ea.
  3. Connect to rate: More successful collisions per second means a faster rate.
  4. Write the full answer: At 50 °C, particles have greater average KE, so a larger fraction of collisions have energy ≥ Ea. More collisions are successful each second, so the rate increases. Do not stop at “particles move faster”; connect it to activation energy.

Example 2: Comparing Distributions

Curves X and Y show the same gas at two temperatures. Which curve is at the higher temperature? Which has more collisions that can react?

Energy distributions for one gas at two temperatures. Curve X is tall and narrow with its peak at low energy; curve Y is lower and wider, shifted right. A dashed line marks Ea.
Show the solution
  1. Compare the areas: Same gas sample, so the area under both curves is the same.
  2. Compare the shapes: Y is shifted right and flatter, so more particles have high energies: a higher average KE.
  3. Name the temperature: Y is at the higher temperature.
  4. Look past the activation energy: Y has much more area to the right of Ea, so Y has more collisions with energy ≥ Ea.

Example 3: Unsuccessful Collisions

Gas particles collide billions of times every second, but only a small fraction of those collisions make products. Give two reasons a collision might not make products.

Show the solution
  1. Reason 1: Not enough energy (E < Ea), so the needed bonds cannot break and the particles bounce apart.
  2. Reason 2: Wrong orientation, so the right bonds cannot form even with enough energy.
  3. Summarize: A successful collision needs enough energy and the correct orientation. A collision missing either one does not make products.

↑ Back to top


Practice

Practice with the Kinetics and Collision Theory Sandbox

Watch particles collide, change the temperature, the concentration and the activation energy, add a catalyst, and see why only some collisions lead to a reaction.

Lab worksheet: PDF | Answer key: PDF

Practice with instant feedback

Answer original AP-style questions for Unit 5 and see an explanation right after each one. Choose Topic 5.5 or mix topics. No login needed.

↑ Back to top


Lesson Slides

↑ Back to top


Big Ideas

  • Particles must collide to react.
  • A collision works only if its energy is at least Ea and the orientation is correct.
  • Raising the temperature increases the fraction of collisions with enough energy, which speeds up the reaction.
  • Raising the concentration increases the number of collisions per second.

Back to the essential question: Most collisions either do not have enough energy or do not have the right orientation. Successful collision = enough energy + right orientation. Next up, Topic 5.6 Reaction Energy Profile, where activation energy becomes a hill the reactants have to climb.

↑ Back to top


AP Alignment

This lesson covers Topic 5.5, Collision Model, in Unit 5 (Kinetics) of the College Board AP Chemistry Course and Exam Description (CED). Learning objective:

  • 5.5.A: Explain the relationship between the rate of an elementary reaction and the frequency, energy, and orientation of particle collisions.

Essential knowledge: 5.5.A.1, 5.5.A.2, 5.5.A.3

Suggested skill: 6.E Argumentation. Provide reasoning to justify a claim using connections between particulate and macroscopic scales or levels.

↑ Back to top