In this lesson
Take it with you
- Lesson slides (PDF)
- Practice worksheet (PDF)
- Answer key (PDF)
- Reaction Energy Lab (activity)
- AP Chemistry Unit 6 Practice (activity)
Essential Question
How can a picture show if energy is released or absorbed?
In Topic 6.1 you used temperature changes to decide which way energy flows. In this topic you will draw that energy change as a diagram, so you can see at a glance whether a process is endothermic or exothermic.
Video not loading? Watch it on YouTube.
Parts of an Energy Diagram
- The y-axis is potential energy, the energy the chemicals have because of the attractions between their particles and the bonds holding their atoms together.
- The x-axis is reaction progress, from start to finish.
- One level shows the reactants and another shows the products.
- The ΔH arrow always starts at the reactants and points to the products.

Exothermic Diagram
- Products are lower than reactants.
- ΔH < 0 (negative).
- The difference in energy is released to the surroundings.

Endothermic Diagram
- Products are higher than reactants.
- ΔH > 0 (positive).
- The system absorbs energy from the surroundings to get there.

Finding ΔH
ΔH = Eproducts − Ereactants
- Products lower: ΔH is negative (exothermic).
- Products higher: ΔH is positive (endothermic).
- Always final minus initial, so the arrow starts at the reactants.
Energy as a Reactant or Product
You can also show the energy change by writing energy into the equation itself.

- Exothermic: A → B + energy. Energy is a product.
- Endothermic: A + energy → B. Energy is a reactant.
The Hump: Activation Energy
- Most reactions need some energy to get started. This is the activation energy, Ea, the height of the hump measured from the reactants.
- ΔH depends only on the starting and ending levels.
- The hump does not change ΔH. You will study the hump more in Unit 5.

Phase Changes on an Energy Diagram
- Gas has the highest potential energy and solid has the lowest.
- Moving up (melting, vaporizing) is endothermic.
- Moving down (freezing, condensing) is exothermic.

Worked Examples
Try each problem on your own first, then open the solution to check your work.
Example 1: Sketch a Diagram
The combustion of methane releases energy: CH4(g) + 2O2(g) → CO2(g) + 2H2O(l), ΔH = −890 kJ/molrxn. Sketch and label an energy diagram for this reaction.
Show the solution
- Draw and label the axes: potential energy on the y-axis, reaction progress on the x-axis.
- Draw the reactant level high on the left and label it CH4 + 2O2.
- Draw the product level lower on the right and label it CO2 + 2H2O. It is lower because ΔH is negative.
- Draw the ΔH arrow from the reactant level down to the product level and label it ΔH = −890 kJ/molrxn.
- Answer: Products lower than reactants, with a downward ΔH arrow. The reaction is exothermic.
Example 2: Read a Diagram
Use the energy diagram to determine ΔH for the reaction. Is the reaction endothermic or exothermic?

Show the solution
- Read the levels: reactants are at 120 kJ and products are at 180 kJ.
- Calculate: ΔH = Eproducts − Ereactants = 180 kJ − 120 kJ = +60 kJ.
- Classify: the products are higher than the reactants.
- Answer: ΔH = +60 kJ. The reaction is endothermic.
Watch out: do not use the peak. 250 − 120 = 130 kJ is the activation energy, not ΔH.
Example 3: Match the Diagram
An instant cold pack gets cold when the solid dissolves. Which diagram represents the dissolving process? Justify your answer.

Show the solution
- Use the evidence: the pack gets cold, so the surroundings lose energy.
- Direction of energy flow: the system (the dissolving solid) absorbs that energy. The process is endothermic.
- Match the picture: endothermic means the products end higher than the reactants, so ΔH > 0.
- Answer: Diagram B. The products are higher than the reactants, which shows energy absorbed from the surroundings.
Practice
Run the Reaction Energy Lab
The lab opens in Energy diagram with an endothermic reaction. Change the reactant, product, and peak energies, add a catalyst, and read ΔH and Ea from the diagram. No login needed.
Practice with instant feedback
Answer original AP-style questions for Unit 6 and see an explanation right after each one. Choose Topic 6.2 or mix topics. No login needed.
Lesson Slides
Big Ideas
- Products lower: exothermic, ΔH < 0.
- Products higher: endothermic, ΔH > 0.
- The ΔH arrow points from reactants to products.
- The hump (activation energy) does not change ΔH.
Back to the essential question: an energy diagram shows where the products end up compared to the reactants. If they end lower, energy was released. If they end higher, energy was absorbed. Next up, Topic 6.3 Heat Transfer and Thermal Equilibrium, where you will look at how energy actually moves between particles.
AP Alignment
This lesson covers Topic 6.2, Energy Diagrams, in Unit 6 (Thermochemistry) of the College Board AP Chemistry Course and Exam Description (CED). Learning objective:
- 6.2.A: Represent a chemical or physical transformation with an energy diagram.
Essential knowledge: 6.2.A.1
Suggested skill: 3.A Representing Data and Phenomena. Represent chemical phenomena using appropriate graphing techniques, including correct scale and units.